Quick answer
Use the Sarissa Stencil System - Hazard Markings with a dry brush and thin, built-up coats. Tape the stencil flat, load the brush lightly, and brush from the stencil edge into the gap to keep stripes crisp on MDF terrain.
Why MDF terrain needs a stencil for hazard stripes
MDF has a slightly porous, fibrous surface that can wick paint under a loose mask. A stencil held flat and brushed with a dry brush limits seepage and keeps the edges of warning markings sharp. Freehand stripes are possible, but consistent spacing and angle across multiple pieces is much harder to repeat without a template.
The stencil is sized for 28mm down to 15mm scale, so the same pattern works across different terrain sets. That makes it a practical choice when you want hazard markings to look consistent on a whole table rather than on a single piece.
When a stencil is the wrong tool
If your terrain has deep texture, rivets, or heavily weathered surfaces, a flat stencil will not sit flush and paint will creep under the edges. In that case, mask the area with tape and cut the stripes by hand, or reserve the stencil for flat panels and walkway edges.
Very small scales below 15mm may find the pattern too large for the surface. Check the stencil against the model before committing; if the spacing looks oversized, use only part of the pattern or switch to a finer freehand line.
Step-by-step: painting hazard stripes with the stencil
- Prepare the MDF surface: Seal or prime the MDF first and let it cure fully. Sand any raised fibers flat before stenciling. Common mistake: painting onto bare, fuzzy MDF, which lets paint bleed along the fibers. Checkpoint: the surface should feel smooth and dry before you tape the stencil down. A sealed, smooth surface is the first defense against bleed.
- Position and secure the stencil: Lay the stencil flat and align the pattern with the edge or panel you are marking. Tape all four sides with low-tack tape so it cannot shift. Common mistake: taping only two sides, which lets the stencil lift as you brush. Checkpoint: press down the edges and confirm no gaps. Tape every edge; a lifted corner ruins the line.
- Load the brush lightly: Dip a dry brush into your paint, then wipe most of it off on a paper towel until the bristles barely transfer color. Common mistake: using a wet brush, which pushes paint under the stencil. Checkpoint: test on scrap first; the brush should leave a faint, dry streak. Dry brush, not wet paint, is what keeps edges sharp.
- Brush from the stencil into the opening: Brush from the stencil surface toward the center of the cutout, not from the open area outward. Use light, repeated passes to build coverage. Common mistake: brushing outward, which lifts the stencil edge and forces paint underneath. Checkpoint: keep the stencil pressed down as you work. Direction matters as much as paint load.
- Build thin coats and let them dry: Apply two or three thin passes rather than one heavy coat, allowing each to dry to the touch. Common mistake: flooding the stencil to save time, which causes seepage. Checkpoint: if paint appears under the edge, stop and clean it before continuing. Thin coats dry fast and stay inside the lines.
- Remove the stencil cleanly: Peel the tape and lift the stencil straight up while the paint is still slightly tacky, not fully hard. Common mistake: pulling at an angle, which can flake the fresh edge. Checkpoint: lift slowly and check the stripe edges before the paint sets. Lift straight up at the tacky stage for the cleanest edge.
Product facts
- Sarissa Stencil System - Hazard Markings: The Sarissa Stencil System is a range of tough and durable Mylar stencils for dry brushing and detailing MDF or other model kits. Mylar resists paint and repeated brushing, so the stencil stays flat and reusable across a whole terrain set.

Sarissa Stencil System - Hazard Markings - Sarissa Stencil System - Hazard Markings: This hazard markings stencil is ideal for 28mm down to 15mm scale and measures approximately 74x105 mm (A7). The A7 size fits easily on walkways, barriers, and vehicle panels while covering enough area for a full stripe run.


